SeaDoo RX Instrukcje Operacyjne Strona 57
- Strona / 91
- Spis treści
- ROZWIĄZYWANIE PROBLEMÓW
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
55
MAINTENANCE
Maintenance, replacement, or repair
of the emission control devices and
systems may be performed by any
marine SI (spark ignition) engine re-
pair establishments or individual.
Lubrication
Use SEA-DOO synthetic grease or
equivalent and lubricate PTO flywheel.
Proceed as follows:
Remove seat to expose engine com-
partment.
Remove vent tube support (if so
equipped).
PTO Flywheel
Remove the fasteners and pull out PTO
flywheel guard.
TYPICAL
1. Flywheel guard
2. Fasteners
Using a grease gun, carefully lubricate
PTO flywheel at grease fitting until
PTO flywheel boot begins to expand.
CAUTION: Immediately stop lubri-
cating as soon as PTO flywheel boot
begins to expand to prevent damage
or slipping.
1. PTO flywheel
2. Grease fitting
3. PTO flywheel boot
Reinstall and secure PTO flywheel guard.
Anticorrosion Protection
Throttle/Choke Cables
Lubricate the throttle and choke cables
(if so equipped) with BOMBARDIER
LUBE lubricant or equivalent.
Electrical Connections
As necessary, apply anticorrosion prod-
uct such as dielectric grease on battery
posts and all exposed cable connectors.
CAUTION: Do not lubricate connec-
tors of the Multi-Purpose Electronic
Module.
Additional Lubrication
BOMBARDIER LUBE lubricant or equiv-
alent will help prevent corrosion of me-
tallic parts and maintain proper opera-
tion of moving mechanisms.
WARNING
Only perform procedures as de-
tailed in this guide. It is recom-
mended that the assistance of an
authorized Sea-Doo dealer be peri-
odically obtained on other compo-
nents/systems not covered in this
guide. Unless otherwise specified,
engine must not be running and the
safety lanyard must be removed
from its switch for all maintenance
procedures. Components inside
engine compartment may be hot.
F01I0AY
2
1
WARNING
Do not lubricate the safety lanyard
post.
F01I0BZ
2
1
3
smo2000-003a.book Page 55 Thursday, November 11, 1999 10:44 AM
www.SeaDooManuals.net
- Videocassette 3
- Operator’s Guide 3
- Safety Handbook 3
- Piloting 3
- TABLE OF CONTENTS 4
- FOREWORD 7
- SAFETY WARNING 8
- Maintenance 11
- LIST OF DISTRIBUTORS 12
- AMERICA: 2000 SEA-DOO 13
- WATERCRAFT 13
- WARRANTY: 2000 SEA-DOO 15
- REGISTRATION NUMBER LOCATION 17
- Label 1 Label 2 18
- DO NOT BOOST BATTERY 19
- WHILE INSTALLED 19
- IDENTIFICATION NUMBERS 20
- RX/DI Models 21
- GTX DI Models 22
- COMPONENTS FUNCTIONS 24
- 2) Handlebar 25
- 3) Throttle Lever 25
- 4) Engine Start/Stop 25
- All Models 26
- Carburetor-Equipped Models 26
- RX Models 26
- 1. Position indicator 28
- 2. Bow up 28
- 3. Bow down 28
- 10) Glove Box 30
- 11) Fuel Tank Valve 30
- 12) Fuel Tank Cap 30
- 13) Oil Injection Reservoir 30
- Step : Lift 31
- 1. Holder 31
- 19) Seat Latch 32
- 30) Flushing Connector 35
- 31) Bilge Drain Plugs 35
- 32) Jet Pump Nozzle 35
- 33) Reverse Gate 35
- 34) Jet Pump Water Intake 35
- FUEL AND LUBRICATION 36
- Oil Injection System 37
- BREAK-IN PERIOD 38
- DAILY PRE-OPERATION CHECKS 39
- 1. Inspect this area 40
- OPERATING INSTRUCTIONS 42
- 3. Nozzle up 44
- Boarding the Watercraft 45
- A. 90 cm (3 ft) 46
- Starting the Engine 47
- Rough Water or Poor 48
- Visibility Operation 48
- Crossing Waves 48
- Stopping/Docking 49
- Beaching 49
- Shutting Off the Engine 49
- POST-OPERATION CARE 50
- DI Models 51
- Anticorrosion Treatment 52
- SPECIAL PROCEDURES 53
- Capsized Watercraft 54
- Submerged Watercraft 54
- Water-Flooded Engine 54
- Fuel-Flooded Engine 55
- Out of Fuel 56
- Towing the Watercraft in 56
- Low-charge Battery 56
- Condition 56
- MAINTENANCE 57
- Periodic Inspection 58
- Periodic Inspection Chart 59
- WARNING 61
- VTS Adjustment 62
- (if so equipped) 62
- Vacuum Bailer Pick-Ups 62
- General Inspection and 64
- Cleaning 64
- TRAILERING, STORAGE 65
- AND PRE-SEASON PREPARATION 65
- 1. Bleed outlet hose 69
- 1. Engine drain hose 69
- 1. Water regulator valve 69
- 2. Supply hose 69
- Pre-Season Preparation 70
- Pre-Season Preparation Chart 71
- TROUBLESHOOTING 72
- Engine Will Not Start 73
- Engine Overheats 74
- Engine Continually Backfires 74
- Engine Pinging or Knocking 74
- SPECIFICATIONS 76
- SI* METRIC INFORMATION 80
- DEALER IMPRINT AREA 82
- CHANGE OF ADDRESS 83
Powiązane produkty i podręczniki dla Silnik SeaDoo RX
Silnik SeaDoo GTI LE Instrukcja Użytkownika
(22 strony)
(22 strony)
Silnik SeaDoo GSI Instrukcje Operacyjne
(105 strony)
(105 strony)
Silnik SeaDoo GTX 4-TEC Instrukcje Operacyjne
(104 strony)
(104 strony)
Silnik SeaDoo GTI LE Dokumentacja
(130 strony)
(130 strony)
Silnik SeaDoo GS Instrukcje Operacyjne
(109 strony)
(109 strony)
Silnik SeaDoo GTI LE RFI Dokumentacja
(121 strony)
(121 strony)
Silnik SeaDoo GSX Limited Instrukcja Użytkownika
(11 strony)
(11 strony)
Silnik SeaDoo XP DI Instrukcje Operacyjne
(24 strony)
(24 strony)
Silnik SeaDoo SP Instrukcja Obsługi
(316 strony)
(316 strony)
Silnik SeaDoo GS Instrukcje Operacyjne
(100 strony)
(100 strony)
Silnik SeaDoo GSX Instrukcja Obsługi
(56 strony)
(56 strony)
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.040 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji